Is your Audi A3 rear wiper not working? Here are a few reasons why it might be causing a problem, and what you can do about it.
Have you ever been driving in the rain and had your rear wiper not work? This can be a very frustrating experience. When the visibility is low, or you need to reverse your car rear wiper helps you drive safely.
Hence it is essential to keep the rear wiper in working condition.
This blog post will show you how to fix the rear wiper on your Audi A3. We will also provide tips on preventing this from happening again. Keep reading for more information.
Reasons Of An Audi A Rear Wiper Malfunctioning
Various reasons could cause the rear wiper of your Audi A to malfunction. It could be due to a problem with the wiper motor, the fuse, or the switch.
Sometimes, it might also be caused by a blockage in the wiper blade. Here are some of the most common reasons for an Audi A rear wiper malfunction:
1. Wiper Motor Problem
The wiper motor is responsible for moving the wiper blades back and forth. If there is a problem with the motor, it can cause the rear wiper to malfunction.
You will need to have the motor checked and replaced if necessary. This is a common fault that occurs in many Audi A3 cars.
Also read – What to do if there is no communication with ECU in Audi A6
2. Fuse Problem
If the fuse that controls the rear wiper is blown, it will cause the wiper to malfunction. You will need to replace the fuse with a new one. To replace the fuse, remove the gear box behind the left hand steering wheel.
3. Switch problem
If the switch that controls the rear wiper is not working correctly, it can also cause the wiper to malfunction. You will need to have the switch replaced.
4. Blockage in Wiper Blade
If there is a blockage in the wiper blade, it can prevent the blade from moving correctly. This can cause the rear wiper to malfunction. You will need to clean or replace the wiper blade.
You must also clean the two rear washer jet that ejects water very carefully using a thin wire or a pin.
If you are having problems with your Audi A rear wiper, it is essential to have it checked by a professional. They will be able to diagnose the problem and make the necessary repairs.
You might also like to read: Mondeo Central Security System Not Working On A Door
How To Test Rear Wiper Motor?
If your rear windshield wiper motor isn’t working, it could be a sign of a bigger problem. Luckily, testing the motor is relatively simple and can be done at home with a few tools. To test the rear wiper motor, you’ll need:
- A multimeter
- A voltmeter
- A 12-volt battery
- A test light (optional)
First, disconnect the negative (-) lead from the battery gear. Then, using your multimeter connector wiring, test for continuity between the two terminal points on the motor.
If there is no continuity, the motor is most likely faulty and needs to be replaced.
Next, connect the positive (+) lead from the battery to one of the terminal points on the motor. Then, using your voltmeter, test for voltage at the other terminal point. If there is no voltage, the motor is probably faulty and needs to be replaced.
If you have a test light, you can also use that to test for voltage at the other terminal point.
Connect the positive (+) lead from the battery to the terminal point and then touch the tip of the test light to the other terminal point.
If the light comes on, voltage is present, and the motor is most likely working correctly.
Once you’ve tested the boot wiper motor, you’ll need to replace it if it’s not working correctly. Be sure to disconnect the negative (-) lead from the battery before starting any work on the motor.
How To Remove Rear Wiper On Audi A3?
Follow these steps to remove the Rear screen wash on your Audi A3:
- Locate the screws that hold the wiper in place.
- Remove the nuts that secure the wiper arm to the motor.
- Pull the wiper off of the windshield.
- Repeat these steps for the other side of the rear wiper.
- Once both sides have been removed, you can gently pull the rear wiper off the vehicle.
- You may need to use a little force to remove the rear wiper, but be careful not to damage the windshield.
You might also like to read: Speedometer And Gas Gauge Not Working
Frequently Asked Questions
How do you turn on the rear wiper on an Audi a3?
Press the wiper control stalk down to turn on the rear wiper on an Audi a3. This will engage the rear wiper.
To turn off the rear wiper, press the wiper control stalk up. If you want to activate the intermittent setting, press the wiper control stalk up and release.
The rear wiper will then operate at intermittent speeds. The rear wiper will then wipe at intermittent intervals.
Where is the fuse for the rear windshield wiper?
If your rear windshield wiper isn’t working, the first thing you’ll want to check is the fuse.
The location of the fuse will vary depending on your car’s make and model, but it is usually located in the fuse box under the hood.
Once you’ve found the fuse, replace it with a new one and see if that solves the problem. If not, there may be another issue at play.
Also read: Audi Traffic Sign Recognition Not Working
How do you know if your wiper motor is bad?
If your wipers are not working correctly, you can check a few things to see if the problem is with the motor:
- Ensure that the wipers are turned on and the blades are not obstructed. If they are, clear the obstruction and try again.
- Check the fluid level in the reservoir; if it is low, refill it and see if that fixes the problem.
- If neither of those solutions works, it is likely that the wiper motor itself is bad and will need to be replaced.
Conclusion
Keeping a car in good condition is all you need to stay safe. You should diagnose your car problems now and then so that you can react to the issues promptly and without any delay.
It’s not always easy to diagnose car problems.
Hopefully, this article has helped you understand the Audi A3 rear wiper problem. If you have any other questions or concerns, contact us for more help. We are here to assist you in whatever way we can!
