If you are thinking of tinkering with your Chevy’s brake calipers then you must first know what size Torx Bit for Chevy brakes works best for which wheel. We will answer this and much more in the article below.
When driving through a congested road you need to make extensive use of your brake. The function requires the use of all the parts of the brake. At a critical moment, if you suddenly feel the brake system giving up, this would cause panic.
To stay clear of such accidents it is necessary to take good care of your brake caliper. Any loose screws in the braking mechanism can be hazardous for both the car and the people in the car. The driver should feel uncomfortable vibrations in that situation. It can be a warning for further complications.
These days it is difficult to find automobile mechanics at your beck and call. To fix minor problems in your car you should have a sane knowledge of the mechanisms.
To fix your brake caliper it is necessary to have Torx bits and screws in your hardware box. You should also know about the different sizes of Torx bits and the ones needed for your brake caliper.
I will walk you through every small detail of Torx bits and the things you would need to fix your car. Stay tuned for the cost and other information.
You might like to read: What Size Wrench For Brake Bleeder Valve?
What is a Brake caliper?
The brake caliper is an important part of the disk brake system. It acts as a bracket to support the brake disks and sometimes the brake calipers themselves.
It squeezes the brake pads against the rotors to stop the car. There are two types of brake calipers- the dual piston and the single piston. In most cars, the front brake has dual pistons and the rear brake uses single pistons.
The brake caliper of a car can deteriorate because of warped rotors or worn-out rotor pads. In both situations, the heat produced in the car is held in. This is a major cause of broken-down brake calipers.
If the brake calipers of a car break down, the car will behave weirdly. Your car may pull itself towards the operating brake. The braking distance of the car will increase. On rare occasions, the caliper will snap. The driver will hear a clunking sound whenever they brake. If this happens it is advisable to stop the car and not operate it.
Also read: What Size Allen Wrench Is Right For Chevy Brake Calipers?
What is a Torx Bit?
Torx is the trademark type of screwdriver that has a 6 points star-shaped pattern. It was developed by Camran Textron in 1967. It is also known as star screwdriver, star bits, and Torx bits. Torx Bits are mainly used in automobiles.
This tool is in high demand in the engineering sector as well. Torx bits are useful for a lot of automobile repairs. Torx screws are exceptionally strong and are thus used in cars and jeeps.
What Size Torx Bit To Use For A Chevy?
Sizes of a Torx Bit
Sometimes you might be confused about which Torx bit to purchase. In other situations, the socket may feel like it’s not gripping tight enough. To solve these you need to have a steady knowledge of the different sizes of a Torx bit.
There are two types of Torx fasteners, external and internal. There are different tools for different purposes. For external bolts, it is advisable to use Torx sockets. For internal screws, Torx bits are used.
You might like to read: What Size Bolt To Remove Silverado Brake Rotor?
What Torx Bit to use for a Chevrolet Brake
- For the rear brakes of a Chevy 2500, the T55 Torx bit is used. The same bits would work for a ‘02 GMC and a ‘03 Yukon.
- A 2001 Chevrolet Silverado 2500HD LS Crew Cab LB 4WD would use a T-70 Torx bit to remove the brake caliper.
- For a ‘07 LMM Chevy Reg Cab 2500HD, you can use a T55 Torx bit. You should clean and grease them before use.
- You can use a T55 Torx bit for a 2015 Silverado 1500 LT Crew Cab.
- For the front caliper bolts of a 2002 Chevy Silverado 1500 5.3 v8 Vin T, you would need the T50 Torx bits.
- For the front calipers of the 1999-2013 Silverado and Sierra 1500, you would need the T50 Torx bits.
- For a ‘04 Chevy Suburban, you would need the T55 Torx bits.
- For a ‘99 Silverado 2005, you would need the T55 Torx bits.
Most Chevy brakes use either a T55 or a T50 Torx bit for the calipers. The newer models of the Chevy are prone to excessive wearing out of the brake pads. Hence it is advisable to always keep the mentioned tools with you. A Torx screwdriver will cost you around $300. It will cost you around $5oo to $900 to replace your brake calipers at the mechanic.
Also read – Chevy Truck Rear End Interchange: How To Work With It?
The Tools You Would Need To Remove A Brake caliper
To remove or replace brake calipers you would need the following tools:
- A jack or a jack stand to hold up the car.
- A lug wrench to remove the lug nuts from the wheel.
- Sockets and rackets to remove the calipers from suspension.
- A line wrench to remove the brake line.
- A line clamp or plug to refrain the brake fluid from flowing out.
- A hammer if the brake pads are clamped to the rotors.
- Screwdrivers or Torx bits to pull out the screws and retainers.
- A set of brake pad spreaders to provide enough space to mount the new calipers.
- A vacuum pump to make sure there’s no air when replacing the caliper and brake line.
- You should also fill up the brake fluid if you have accidentally spilled any.
How To Tighten A Brake Caliper?
A very easy method of making sure your car is safe on the road is by inspecting the calipers. You can tighten the calipers if needed. To do that you have to follow a few simple steps:
- Remove the brake caliper bolts using screwdrivers and Torx screws. Make sure you install them back incorrectly.
- Take note of the caliper bolt and bolt holes. If they have accumulated rust, replace them.
- You can also clean or re thread the bolt holes using a thread cleaner or a thread chaser.
- Follow your vehicle manual and install all the parts correctly.
- Using the recommended torque pressure and Torx bits tighten the brake caliper bolts.
You might like to read: What Size Tire Iron Do I Need?
Frequently Asked Questions
#1. How To Tighten Brake Caliper Bolts?
To tighten the Brake Caliper Bolts, use a Torx bit. Slowly guide the bolts into the spindle using the said tool. This will prevent brake malfunctions.
#2. What Type of Torque Wrenches do you need?
The type of malfunction will determine the type of torque wrench needed. For oil changes and tightenings, you will need light-duty torque wrenches.
#3. What Torx size does a chevy use?
Different models will use different sizes of Torx bits. Most Chevys will need a T55 or a T50 Torx bit.
#4. Where to buy Torx bits?
You can find Torx bits at hardware shops. You can also find them in online shops.
You might like to read: What Size Master Cylinder For 4 Wheel Disc Brakes?
A Few Final Words
Now you have enough information about the best Torx bit for your Chevy. You should learn how to solve mechanical problems as well. It is always safe to take care of minor problems to keep them from becoming big. The initial investment on the Torx bits will stop stinging you once you save big bucks at the mechanic.
Thank you for reading the article, we hope we answered everything you needed to know about Torx Bits for Chevy brake calipers. If you have more doubts, reach out to us with your questions in the comments section and we will get back to you.
